BS 3066-1995
|
ID： |
3F5BAD70E5914F59A1D19BB191C9D1CD |
|
文件大小(MB)： |
0.85 |
|
页数： |
26 |
|
文件格式： |
|
|
日期： |
2013-6-23 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
B S I BS*3Obb 75 = Lb24bb?043765b Tbb,~~,BRITISH STANDARD,Specification for,Engineers’ cold chisels,and allied tools,UDC 621.911 3,rn,BS3066 : 1995,Copyright British Standards Institution,Reproduced by IHS under license with BSI - Uncontrolled Copy,No reproduction or networking permitted without license from IHS Not for Resale,--`,,`,`,-`-`,,`,,`,`,,`---,B S I BSW3Obb 75 1ib24bb?0437657 ?T 2 m,BS 3066 : 1995,This British Standard, having,been prepared under the,direction of the Machine,Engineers and Hand Tools,Standards Policy Committee,was published under the,authority of the Standards,Board and comes into effect on,15 January 1995,O BSI 1995,The following BSI references,relate to the work on this,standard:,Committee reference MTE/15,Draft for comment,93/702684 DC,ISBN O 580 22876 2,Committees responsible for this,British Standard,The preparation of this British Standard was entrusted by the Machine,Engineers and Hand Tools Standards Policy Committee (MTEI-) to Technical,Committee MTE/15, upon which the following bodies were represented:,British Coal Corporation,British Telecommunications plc,Consumer Policy Committee of BSI,Federation of British Hand Tool Manufacturers,Handle Manufacturers’ Association,Institute of Carpenters,Ministry of Defence,The following bodies were also represented in the drafting of the standard,through subcommittees and panels:,British Steel Industry,Coopted members,Amendments issued since publication,I Text affected,Amd. No. 1 Date,Copyright British Standards Institution,Reproduced by IHS under license with BSI - Uncontrolled Copy,No reproduction or networking permitted without license from IHS Not for Resale,--`,,`,`,-`-`,,`,,`,`,,`---,B S I BS*3Obb 95 Lb24bb9 0439658 839 - BS 3066 : 1995,~~~,Contents,Committees responsible,Foreword,page,Inside front cover,3,Specification,1 Scope,2 References,3 Material,4 Types and dimensions,5 Heat treatment and hardness,6 Finish,7 Marking,8 Qsts,Annexes,A,B (normative) Rsts,ables,(informative) Guidance on the safe use of chisels and allied tools,1,2,3,4,5,6,7,8,9,10,11,12,13,14 Hardness levels for punches,15,Material specification for carbon steel tools,Nominal dimensions of flat cold chisels,Nominal dimensions of cross-cut cold chisels,Nominal dimensions of half round-nose cold chisels,Nominal dimensions of diamond-point cold chisels,Nominal dimensions of brick bolsters,Nominal dimensions of floorboard chisels,Nominal dimensions of plain and fluted plugging chisels,Nominal dimensions of concrete or moil points,Nominal dimensions of parallel pin punches,Nominal dimensions of taper punches (including nail and reaper,punches),Nominal dimensions of centre punches,Hardness levels for chisels, bolsters and concrete points,Hardness zone at the cutting edge for chisels, bolsters and concrete,points,19,22,4,6,7,8,9,10,11,12,13,14,15,16,17,17,17,Copyright British Standards Institution 1,Reproduced by IHS under license with BSI - Uncontrolled Copy,No reproduction or networking permitted without license from IHS Not for Resale,--`,,`,`,-`-`,,`,,`,`,,`---,B S I BS*30bb 95 W Lb24bb?0439b59 775 W,BS 3066 : 1995,Figures,1 Flat cold chisels,2 Cross-cut cold chisels,3 Half round-nose cold chisels,4 Diamond-point cold chisels,5 Brick bolsters,6 Floorboard chisels,7 Plain and fluted plugging chisels,6,7,8,9,10,11,12,8 Concrete or moil points 13,9 Parallel pin punches 14,10 %per punches 15,11 Centre punches 16,List of references Inside back cover,12 Typical hand guards 18,Copyrigh2t B ritish Standards Institution,Reproduced by IHS under license with BSI - Uncontrolled Copy,No reproduction or networking permitted without license from IHS Not for Resale,--`,,`,`,-`-`,,`,,`,`,,`---,BSI BS*30bb 95 M 1624669 0439660 497 M,BS 3066 : 1995,Foreword,This British Standard has been prepared under the direction of the Machine,Engineers and Hand Tools Standards Policy Committee, and supersedes BS 3066 :,1981 which is withdrawn.,Matters concerning safety cannot be too strongly emphasized and it is a prime,requirement that a safe tool should be offered to the user.,Since publication of the original specification, the design of chisels and,manufacturing techniques employed have continued to improve. It is not the,intention of this standard to impose restrictions on the types of materials from,which chisels may be manufactured, and so inhibit development in this direction,but greater importance is placed on tests and testing procedures.,It should be recognized that cold chisels and aliied tools are prone to work,hardening and that the hardness values quoted in tables 13 to 15 apply only at,the time of manufacture.,In so far as the user is concern……
……